Monday, March 25, 2024
Menu

How to clean plastic parts on the car!

Reading time 4 Min.

How to clean plastic parts on the car!

A car that is clean and tidy, both inside and out, makes a good impression on your passengers and colleagues. It also maintains the value of the car and counteracts deterioration. Removing dirt and stones from the seats and floor mats is one thing, but also that plastic surfaces should be clean and attractive. We will therefore tell you how to clean the plastic parts, without that residues or dull surfaces remain.

How to clean plastic parts on the car!

Step-by-step instructions for breastfeeding with the emeibaby carrier:

  1. Carefully and without scratching the plastic surfaces of dead flies, crumbs, leaves and dirt to free. A brush attachment protects against scratches in the plastic. Before deep cleaning, remove coarse particles from small recesses, the glove box and other plastic parts.
  2. With a damp rag or a soft one feather duster the dust can be removed. Hard-to-reach places such as the gear stick, the handbrake, the radio or narrow niches can be softened with a little Brush be achieved.
  3. If the plastic is particularly thick, coarse, and textured in certain areas, a harder one should be used brush to be used. In order not to scratch the plastic, the brush should not be too hard.
  4. Spray a small area with a special one Plastic cleaner or cockpit cleaner and wipe off the cleaning agent with a dry cloth. Only work with a clean rag to avoid spreading the dirt.
  5. The cleaning solution not only removes the dirt, but also wax residue or the protective film from any previous cleaning. The current protective film should easily suffice.
  6. Subsequently, the same areas can be used again with a slight wax or protective polish polished, always with a clean piece of cloth. Apply the polish to the material with more intense pressure so that it is well absorbed.
  7. Don't overdo it pressure, so that no material changes occur and unsightly areas remain.
  8. When working with wax can be a small brush may be needed to remove wax residue from textured or tight areas.
  9. Wipe the plastic surfaces once a week with a clean cloth or feather duster so that the dust can be removed immediately. In this way, the plastic remains beautifully shiny and well-groomed until the next cleaning procedure.
  10. Finished.

Tip: Plan about every two months a thorough cleaning of the plastic surfaces of your car. If the climate is very humid and high, you should even clean it intensively every month in order to properly care for the plastic and to prevent stubborn dirt from developing in the first place.

The following note is essential: For safety reasons, tuningblog recommends all repair, inspection and maintenance work exclusively to be carried out in a specialist workshop! Although our information is summarized to the best of our knowledge and belief, we cannot assume any liability for the content. All information is therefore "without guarantee".

Of course, that wasn't the end of it!

In this tuningblog category there are guides and instructions for common defects/repairs on the vehicle and for installing accessories/tuning parts. Our articles explain in a simple way common defects and the corresponding repairs, as well as explaining how the first signs of a defect become noticeable. In most cases, we also have initial clues to the repair instructions in our repair instructions approximate The costs of the pending repair are listed. The goal of our subcategory “Auto Repair Guide“ is to create a head start in knowledge for the next visit to the workshop with initial tips. This may save you from tedious troubleshooting and small things can perhaps be done directly on your own. The same applies, of course, to the installation of accessories/tuning parts. Here, too, we would like to help with the implementation with instructions and tips. There are many other posts on this as well. Below is an excerpt of the last and HERE there are all previous instructions:

Cylinder head / cylinder head gasket defective? The info!

How to clean plastic parts on the car!

Give the car a new paint job yourself!

How to clean plastic parts on the car!

Topping up oil in the hydraulic jack, this is how it works.

How to clean plastic parts on the car!

"tuningblog.eu" - we keep you up to date on the subject of autotuning and car styling with our tuning magazine and present you with the latest tuned vehicles from all over the world every day. It's best to subscribe to ours Feed and will automatically be informed as soon as there is something new about this post, and of course also to all other contributions.

About Thomas Wachsmuth

Thomas Wachsmuth - He has been an integral part of tuningblog.eu since 2013. His passion for cars is so intense that he invests every available penny in them. While he dreams of a BMW E31 850CSI and a Hennessey 6x6 Ford F-150, he currently drives a rather inconspicuous BMW 540i (G31/LCI). His collection of books, magazines and brochures on the subject of car tuning has now reached such proportions that he himself has become a walking reference work for the tuning scene.  More about Thomas

Leave a Comment

Your e-mail address will not be published. Required fields are marked with * marked